If you’re looking to replace your current wheels, Chrome wheels are a must if you want your car to stand out. Mirror finish chrome wheels look absolutely wonderful and definitely make heads turn. When switching to chrome however, it is important to maintain them and regularly polish them in order to preserve that finish. Chrome is a delicate metal and might wear if not taken care of. The good news is it can be quite simple to maintain chrome polish and can be done with a few simple DIY tips.
Unfortunately car wheels get exposed to a variety of contaminants which can wear away the look of chrome. Various components such as carbon strands and glue can fall off the brake cushion and minor metal shavings from the rotor. The extreme heat and movement created by the wheels makes these elements damaging to the external look of car wheels. With time, the dust and other elements accumulate and disrupt the smooth functioning of the wheels. Cleaning not only helps maintain the appearance but also safeguards its functionality. Over time this dust can pit chrome wheels so using a proper chrome polish can help maintain their life and of course keep their shine.
First, always clean your wheels with the help of warm water and detergent before polishing. This helps get rid of dust, providing a smooth surface for polishing. You can also use a delicate buffing wheel, though it is not required. The bristles of a soft brush can also help to get rid of dust without scratching chrome. This is vital as scratches are perceptible on chrome. Reach through the spokes to clean every wheel front to back. Don’t overlook the fasteners as dust accumulates anywhere it can.
Make use of a fastener brush to clean around the fasteners and inside the fastener gaps. While you’re working with the brushes, make sure that the wheel is wet. The water and wheel cleaner work on the dust and dirt, and at the same time remove the grease on the surface of the wheel without scratching it. While you’re down there, clean the wheel, which is also known as the bumper wells as a lot of dust and mud gets accumulated with time. You may require something more grounded than what you made use of on the wheels. Splash the wheel liberally with a strong cleaner and with the help of a brush, clean the inner and outer surface of a wheel well. Rinse the haggle well, including the fastener gaps and between the spokes. Make sure to dry the wheel completely before starting off the polishing process as Chrome wheels, specifically, will indicate water spots and they will reduce the mirror wrap up. Make use of a Microfiber Towel to wipe of water spots.
Picking a chrome polish for wheels is important. All the metal polish that can be used on aluminum or steel can also be used on chrome. However before starting with chrome polish it is better to figure out how that metal will react to chrome finish.
Once it is perfectly clean and ready to be worked on, dab some Quick Sheen all metal polish on your wheels. Use a microfiber or terry cloth towel to foment the wheel surface.
First, wipe the polish onto the wheel, applying it to one wheel at a time.
Gradually spread the polish over each wheel. You can let Quick Sheen polish dry without losing any effectivness.
Use a delicate, clean microfiber towel to wipe up the excess polish off each wheel.
Repeat on each of the four wheels, until all have been polished
Once all of your chrome wheels are polished, reapply Quick Sheen all metal polish to seal the wheel surface. This will work exactly like auto wax. Apply the polish the same way as before and afterwards, wipe the wheel clean. This provides a glossy look, and helps break the dust. Quick sheen will dry clear, similar to the wax, so they won’t lessen the sparkle of chrome wheels. Your wheels look cleaner and will maintain the shine for a longer period of time. You should reapply Quick sheen every 6 months; in order to retain the shine. The good news is that the process of cleaning after you have applied Quick Sheen is very simple, as all you need is water to clean and maintain it.
Pick your tire dressing very carefully. Normal tire dressings contains silicone, which provides a polished sparkle but they turn chestnut in color after some time. The reality is that, sparkly silicone tire dressings can accumulate dirt after some time if not maintained frequently. Tire dressings help in maintaining the look of the wheels with a semi-sparkle sheen that doesn’t turn chestnut. You can regularly layer water-based dressings to get a glossier sparkle. Continuously apply flimsy coats and permit drying time before you drive your vehicle. Indeed, even the best dressing will sling off in the event that it’s too thick or hasn’t been dried properly. Abstain from pooling of the dressing around raised letters and white dividers. Quick Sheen tire shine is one of the best at keeping your tires looking good.
To get the best results make use of Quick Sheen to clean your aluminum, amalgam, chrome wheels and more. Many metal polish’s contain smelling salts, anhydrous chemicals or acids which can result in deteriorating the shine due to discoloring and oxidization. For best results, remove the compound wheels and chrome wheels before you start to clean, this will give you best access to the amalgam wheels which would help you see all the areas of the wheel. Get rid of all the dust and dirt and get going with the cleaning. Ensure the wheels are totally perfect and dry. You have to clean between each stage, so that every part is clean. Try and test each and every part of the wheel, start with the most difficult part and with the help of a 600 coarseness, then a 400, clean it as much as possible. After 400 coarseness (if that is the stage you start with), you have to go to a 600. Where conceivable this is best accomplished by going at 90° to the past cut. Once this is done you should be able to clearly see scratches which would help you to concentrate on those parts specifically when you start with polishing. Despite the fact that it is conceivable to machine polish amalgam wheels, brilliant results can be achieved by the home DIY polisher without the use to these equipment with the help of basic directions and proper manual.
Cleaning is like sanding. With a specific end goal which is to make the material brighter and smoother. While cleaning you are expelling the surface of the material so that scratches are removed by polishing. Each material has diverse properties and will buff in a different way. Therefore it is wise to understand the physical properties of the material before starting with the buffing process. In order to be safe, it’s advisable to try buffing on a smaller surface and see how it reacts. If it works fine then you can proceed with the rest.
Polishing is a chemical process which involves reactions, thus can produce harmful gases which when inhaled can cause health and respiratory problems. Therefore it is advisable to follow a few safety instructions. Always carry out polishing in an open space. Cover your hands with gloves which will protect your skin from chemical reactions if any. Try and dress up in cotton clothes rather than synthetic cloths. Wear protective goggles or shades to protect your eyes. Make sure that the area is non cluttered and is well ventilated. It is always advisable to carry out polishing in an open area, rather than in a closed room.
Step 1: Sanding
Figure out whether the material you wish to clean should be sanded first. A simple to follow guideline is if your fingernail can get the edge of a scratch then it should be sanded before it can be cleaned. Continue to Sand in a steady movement without changing direction. Keep sanding until there are any noticeable scratches and a silk completion is accomplished.
Step 2: Select Cleaning Compound and Buffing Wheel
To start cleaning, begin with a stiffer buff, for example, a felt sway or felt cone, sisal buffing wheel, buffing wheel. Embed the buff you wish to begin with into any standard electric drill, seat processor, or buffing machine and pick the coarsest cleaning material by getting in touch with an expert
Step 3: Apply Cleaning Compound
Coat the buffing wheel by delicately turning the buff against the wheel polish. Make use of the mixes sparingly as you just need a little amount of polish for them to work properly. Next, twist the covered buff or felt sway onto the surface to be cleaned. Best results are acquired at 3,000 RPM or less. Working at a higher rate will overheat the work surface and keep the compound from working properly. Keep cleaning as required, reapplying more compound if required. For best results make use of an alternate buff for each cleaning.
Step 4: Repeat
Repeat the procedure for better cleaning till the desired results are obtained. Keep cleaning until visible scratches are expelled and a perfect mirror finish is accomplished
Step 5: Wash and Coat
When work is finished, wash the material with warm lathery water to get rid of any excessive buffing deposit. Pat it dry with a clean cloth. If required apply a wax coat to protect the final polish.